Light intensity is how much light reaches the crop at any moment, measured as PPFD in µmol/m²/s. Light duration is how many hours the light is on. Together they set the daily light integral (DLI), the total light a crop receives per day, measured in mol/m²/day.
Plants respond to both, but in different ways. Intensity drives the rate of photosynthesis, while duration also influences how the crop develops and flowers. Below, we answer the questions growers ask most often about balancing the two in a greenhouse lighting strategy.
How do intensity and duration combine into daily light integral?
Daily light integral (DLI) is the total amount of photosynthetically active light a crop receives over 24 hours. It combines intensity and duration: a higher PPFD or a longer lighting period both raise the DLI. Sunlight and supplemental lighting count toward the same daily total.
The calculation is simple. Multiply the average PPFD (µmol/m²/s) by the number of seconds of light, then divide by 1,000,000 to get mol/m²/day. For example, a constant PPFD of 100 µmol/m²/s for 10 hours gives 3.6 mol/m²/day (100 × 36,000 ÷ 1,000,000).
In a real greenhouse, the calculation is rarely this tidy. Daylight changes by the minute, so you need to account for both natural light and supplemental lighting across the whole day. Light measurements show what the crop actually receives, which is more reliable than estimates.
DLI is a useful target, but it does not describe how the light is delivered. Two greenhouses can reach the same DLI with very different intensity and duration patterns, and the crop may respond differently to each.
Which units measure light intensity and duration in greenhouses?
Light intensity is measured as PPFD in µmol/m²/s. Light duration is measured in hours, as the photoperiod. The accumulated result is the DLI, measured in mol/m²/day. Each unit answers a different question about the light your crop receives.
PAR (photosynthetically active radiation) is the range of light, roughly 400 to 700 nm, that plants use for photosynthesis. It describes the type of light, not a quantity. PPFD (photosynthetic photon flux density) counts the PAR photons reaching a square metre each second, so it shows the intensity at that moment. The photoperiod is the number of hours of light in a 24-hour period, and the DLI is the total PAR received over those 24 hours.
Do not confuse PPFD with lux. Lux measures brightness as the human eye sees it and is not suited to plant lighting. For professional greenhouse work, use a quantum sensor that measures PPFD, and take readings at crop level, not only under the luminaire.
Can longer light duration make up for lower intensity?
Longer light duration can raise the DLI when intensity is low, but it is only a partial substitute. Plants can only use light effectively for so long, and many crops need a dark period. Intensity and duration also affect plant behaviour in different ways.
Adding hours can help close a DLI gap on dark winter days. However, several factors limit this approach:
- Photosynthesis responds to intensity. At a very low PPFD, extra hours add little. A higher PPFD during the same hours may give the crop more usable light.
- Crops need a dark period. Many crops show stress or disorders if the dark period is too short or removed. Tolerance differs between crops and cultivars.
- Photoperiod can trigger development. In some crops, changing the day length changes flowering, not just growth.
- Energy cost matters. Longer lighting hours may fall into more expensive electricity periods, while a lower intensity for more hours may fall into cheaper ones. The right balance depends on your tariff and your crop.
So the answer is partly yes, within the limits of the crop. Treat the crop’s photoperiod requirement as the boundary first, then optimise intensity and hours inside it.
How do photoperiod needs differ between crop types?
Photoperiod needs differ because crops respond to day length in different ways. Some need a long, uninterrupted dark period, some depend on day length for flowering, and others tolerate long lighting hours. The right approach depends on the crop, the cultivar and the growth stage.
Broadly, crops fall into three groups. Short-day crops have flowering that is triggered or supported by shorter days. Many cut flowers and potted plants belong here, and growers often control the photoperiod to steer the crop. Long-day crops flower in response to longer days, so lighting can be used to extend the day. Day-neutral crops are not strongly tied to day length for flowering. Tomatoes and cucumbers are commonly grown this way, so lighting decisions focus more on the DLI.
Even within a group, requirements vary. Tomato and cucumber crops are generally grown with long lighting hours, but some tomato cultivars are sensitive to continuous light, and many growers still keep a dark period. Leafy greens, strawberries, propagation and young plants each have their own needs, which also change across growth stages.
Check the requirements for your specific cultivar and growth stage before extending or shortening the lighting period.
How should growers set intensity and duration with controls?
Set the photoperiod first, based on what the crop needs. Then adjust intensity within that period to reach your DLI target, taking daylight and energy conditions into account. A lighting control system can do this automatically and keep the result consistent.
A practical sequence looks like this:
- Define the crop target. Confirm the DLI range and photoperiod for your crop, cultivar and growth stage.
- Measure natural light. Use sensors to see how much daylight your greenhouse receives, since structure, location and season all change it.
- Fix the allowed lighting window. Decide the earliest start, the latest stop and the required dark period.
- Dim to fill the gap. Dimming changes light intensity, so luminaires add only what the crop needs on top of daylight.
- Factor in energy conditions. Where your system and contract allow, shift lighting toward lower-cost hours without breaking the photoperiod.
- Review and adjust. Compare the measured DLI with the target and refine your settings as the season and crop change.
Dimming is not the same as dynamic spectrum control. Dimming adjusts intensity, while spectrum control changes the wavelength composition of the light. Not every control system supports both, so check what your installation can do.
How Agrolux helps with light intensity and duration
The right balance of intensity and duration depends on your crop, location, natural light, greenhouse construction, existing technology and energy prices. For that reason, we start with your growing situation and treat lighting as a tool that supports your cultivation goals.
Our support includes greenhouse-specific lighting plans and light measurements, and agronomic advice from our plant scientists and agronomists on how light affects your crop. We also offer LED and HPS lighting solutions with attention to heat distribution and greenhouse climate, and lighting control and energy management, including dimming based on daylight and crop requirements. For growers who expect their needs to change, our modular LYRA platform can be adapted over time.
If you want to review your DLI targets, photoperiod or control strategy, we are happy to talk it through. Contact our specialists to discuss your greenhouse and crop, or look at our portfolio for examples of our work.
Related Articles
- How does the timing of supplemental lighting affect plant growth?
- How can growers balance natural daylight and supplemental lighting?
- How does greenhouse lighting affect total cost of ownership?
- How does supplemental lighting support winter greenhouse production?
- How do greenhouse lighting controls respond to changes in daylight?