Light measured above the crop shows how much light reaches the top of the canopy. Light measured within the canopy shows how much reaches the leaves below, after the upper leaves have absorbed, reflected or shaded part of it. Above-canopy readings describe what your lighting system and the sky deliver. In-canopy readings describe what your crop can actually use. This article explains why the two differ, what each one tells you, and how to use them together.
Why do above-canopy and in-canopy readings rarely match?
Above-canopy and in-canopy readings rarely match because leaves absorb, reflect and let through light as it moves down into the crop. Each leaf layer removes part of the photosynthetically active radiation (PAR), which is the light plants use for photosynthesis. As a result, light intensity drops quickly with depth.
How steep that drop is depends on several factors:
- Leaf area and density: A crop with many leaves per square metre of floor (a high leaf area index) catches more light in the upper layers and leaves less for the lower leaves.
- Crop structure: Upright tomato and cucumber plants spread light differently from a flat lettuce canopy or a bushy potted plant.
- Light source geometry: Overhead luminaires, inter-lighting and diffuse daylight enter the canopy at different angles and reach different depths.
- Greenhouse structure: Roof bars, gutters, screens and the type of glass affect how evenly daylight arrives.
- Growth stage: A young crop lets most light pass through. A mature crop catches most of it.
This difference is not a fault. It is a normal result of how plants capture light, and it means a single reading never gives the full picture.
What does each measurement tell a grower about lighting performance?
Above-canopy measurements show how much light your installation and the sky deliver to the crop. In-canopy measurements show how well that light is spread through the plant. Together they show how much light the crop intercepts and how much of it reaches productive leaves.
What above-canopy readings show
Readings above the crop are given as PPFD (photosynthetic photon flux density). This is the number of photosynthetically active photons that reach one square metre each second, measured in µmol/m²/s. It is a value for one moment in time. Added up over 24 hours, it becomes the DLI (daily light integral), measured in mol/m²/day.
Above-canopy data helps you check light uniformity across the greenhouse or compartment, how much daylight contributes at different times of day and year, and whether your lighting plan delivers the intensity it was designed for. It also shows whether your dimming strategy and DLI targets are being met.
What in-canopy readings show
Readings within the canopy show how much PPFD reaches the middle and lower leaves. When you compare them with the above-canopy value, you can see how much light the crop intercepts and how deep it penetrates. Low values deep in the crop may point to heavy shading, a very dense canopy or a light distribution that does not suit the crop stage.
Interpret these numbers with care. Lower leaves are not always short of light in a harmful way. Targets differ by crop, cultivar, growth stage and cultivation goal, so no single in-canopy value applies everywhere.
Which sensors and tools work for in-canopy measurement?
Quantum PAR sensors are the standard tools for in-canopy measurement. They measure PPFD in the 400 to 700 nm range. For canopy work, line (linear) quantum sensors and handheld PAR meters are often the most practical choice, because they average light over a wider area than a single point.
Handheld PAR meters are useful for spot checks, light mapping and checking uniformity at several heights. Line quantum sensors have a long sensing bar that averages light across a row or section of crop, which reduces the error caused by sun flecks and gaps between leaves. Fixed PAR sensors stay in place and log light over time, which supports DLI calculations and trend analysis. Spectrometers are useful when you want to know the spectral composition of the light as well as its intensity.
Single-point sensors can mislead inside a crop. A small sensor may sit in a gap or directly under a leaf and give a reading that is much too high or too low. Taking several readings and averaging them gives a more reliable result. Calibration also matters, as does choosing a sensor that suits your light source, because some sensors respond differently to LED and HPS spectra.
Where should light sensors be placed in a greenhouse crop?
Place above-canopy sensors level at the top of the crop, facing upward, and place in-canopy sensors at several set heights inside the crop. Consistent, repeatable positions matter more than any single location, because they let you compare readings over time and between compartments.
These guidelines help in practice:
- Above the canopy: Keep the sensor level and at a steady distance above the plant tops. As the crop grows, adjust the height so the sensor stays in the same position relative to the plant heads.
- Within the canopy: Measure at several heights, for example in the upper, middle and lower leaf layers. Record each height as a distance from the plant head, not as a fixed height above the floor.
- Across the compartment: Take readings in several positions, including near walls, under gutters, between luminaires and in the centre. This shows uniformity and edge effects.
- Between rows or plants: In row crops, measure both in line with the row and in the gap between rows, as light distribution can differ a lot.
A tilted sensor can read too high or too low, so keep it level. Avoid shading the sensor with your own body or equipment. Measure under comparable conditions, because readings taken under daylight, supplementary light and combined light cannot be compared directly. To see the performance of the lighting alone, measure without daylight or account for daylight separately.
How can both readings be combined to adjust lighting strategy?
Compare the light arriving at the top of the crop with the light reaching the deeper leaf layers. Then adjust light intensity, light distribution or crop management to match what the crop needs. This turns raw numbers into practical decisions about dimming, luminaire placement and crop handling.
During the season, a young crop that lets a lot of light pass through is not yet using all the light available. A mature crop may catch almost everything, so the question shifts to how deep the light penetrates. If the lower leaf layers receive little light, options such as leaf removal, plant density or row spacing may help, within the limits of good crop practice. Large differences between positions at the same height point to uniformity problems in the lighting plan or the greenhouse structure.
Above-canopy data lets you track accumulated light against your DLI target. Keep the photoperiod and the crop’s biological needs in mind, because you cannot freely move light between hours without considering the crop. Measured daylight, forecasts, DLI progress and electricity prices can all inform how much supplementary light to add. Dimming changes intensity only. It is separate from dynamic spectrum control, which changes the spectral composition, and not every control system supports both.
Light changes also affect climate. LED and HPS lamps distribute heat differently, which influences leaf temperature, transpiration and air movement, so review light changes together with your climate settings.
No single setup suits every grower. The right approach depends on your crop, cultivar, growth stage, greenhouse construction, location, daylight levels and energy costs. Treat measurements as evidence that guides adjustments, and check the crop response before making larger changes.
How Agrolux helps with light measurement and canopy light management
At Agrolux, we start from the crop and the way you grow it. Lighting technology is a tool that supports those choices. Our specialists look at your greenhouse, crop and existing technology before advising on any change.
Where it is relevant to your situation, we can help with light measurements that show how light is spread in your greenhouse and how your current installation performs. We can also develop greenhouse-specific lighting plans that take into account your crop, daylight, structure, greenhouse height and energy situation. Our agronomists and plant scientists can discuss how light intensity, duration and spectrum relate to your crop and growth stage. We give objective advice on both LED and HPS lighting, including heat distribution and the effect on your greenhouse climate. We can also look at lighting control and energy management, such as adjusting light intensity based on available sunlight, energy prices and crop requirements, depending on the luminaires and control setup you use. Modular platforms such as LYRA let you start with one configuration and change or expand it later.
If you want to understand how light behaves above and within your own crop, we are glad to talk through your greenhouse, crop and lighting goals. Visit the Agrolux homepage to get in touch with our specialists, or browse our project portfolio to see how we approach different greenhouse situations.
Gerelateerde artikelen
- How does the timing of supplemental lighting affect plant growth?
- How does light quality influence greenhouse crop development?
- How does greenhouse lighting affect total cost of ownership?
- How do greenhouse lighting controls respond to changes in daylight?
- How can greenhouse growers optimise lighting during high electricity prices?